If you lose the first key, you will never approach the vehicle again. You can open the doors, but the motor won’t start no matter how many times you turn the key to one position. so in this post we will know how to bypass ford pats system without key
The Ford PATS system stands for Passive Anti Theft System. It was designed as a security measure to keep thieves and criminals from stealing Ford vehicles.
When the first or original Ford Key is inserted in the vehicle, the PATS sends a message to the car. If a different key is inserted instead of the original, the system will detect it. It distinguishes between genuine and counterfeit keys.
Table of Contents
How To Bypass Ford PATS System Without Key?
Is it safe to say you’re unhappy because you misplaced the main key or are thinking about how to bypass the Ford PATS system without a key? You can, however, unwind. We’ll walk you through the process of bypassing the Ford pats system.
Before we begin, keep in mind that the following steps should not be considered a long-term solution; doing so will leave your vehicle vulnerable to potential vehicle hoodlums. You should simply bypass the Ford Pats system until you obtain another transponder key.
1. Bypassing PATS System
The original key is also known as a transponder key or chip key. Even if you don’t have the original key, the RFID chip from it is required. You’d also need to duplicate the chip key so that it can be used in your ignition.
Before we get started on how to bypass the Ford PATS system without a chip key, you should understand that bypassing the Ford PATS is only a temporary solution that compromises the car’s security.
Get a transponder key as soon as possible to re-secure your vehicle and protect it from car thieves. Without further ado, let’s take a look at how to bypass the pats system on Fords in a few simple steps:
Step 1: Make New Keys
The new keys you just received must match the original key. Take it to a dealer and have the new keys cut so that they match the main key as closely as possible. When it matches the shape of the original chip key, the system will believe you have the correct key.
The system now believes you have the correct key, but you still lack the chip required to bypass the PATS system. This is where the screwdriver comes in.
Step 2: Take out the transponder.
You’ll be able to bypass Pats systems on your Ford vehicle once you have the RFID chip and a matching key. If you remove the transponder from the original key and the chip is not damaged,
1. Pry open the black square at the top of the key with a flathead screwdriver.
2. Avoid applying excessive pressure to avoid breaking the chip.
3. Remove the original key’s transponder.
Step 3: Disable PATS.
You can easily bypass the Ford PATS system with new keys cut to match the original key and the transponder from the original key by following the steps below:
Place the transponder near the ignition so that the chip can be read by the vehicle.
Start the car by inserting the new key into the ignition.
It may take a few tries to figure out where to place the transponder so that it can be read easily.
2. How Do I Reset My Ford PATS System?
If someone tries to start the vehicle with anything other than the PATS key that has been programmed into that vehicle, the PATS system will be activated. This will cause a red light on the scramble to flash faster than usual. The vehicle will remain in this mode until the legitimate key is used or 15 minutes have passed. to know how to bypass the ford pats system without a key or reset the key read all the instructions.
If neither of the above events occurs, the SecuriLock engine immobilizer will activate within the period, allowing your vehicle to be delivered without hesitation. If this happens, you may need to reset the system if the system does not return to normal operation after you use your PATs key to start your vehicle. This will cause a red light to flash on the scramble and
- Insert the PATs key into the start button and turn it.
- Wait 15 minutes until you see the glimmering rate on the red light on your dashboard return to normal speed, and then try both keys again.
- If this does not start the vehicle, open the hood, disconnect the battery for 15 minutes, reconnect it, and try again.
3. How Do You Program Keys In The PATS Module?
Because there are legal issues with Ford vehicles, you must take them to a dealer or locksmith. When you plug the Solus Edge scanner into your vehicle, you can program new keys as follows:
- Scan the device to enable automatic identification.
- Choose “Anti-Theft (PATS)” from the drop-down menu.
- Select “Functional Tests,” then “Security Access.”
- Security access will take ten minutes.
- When the wait is over, you are presented with several options, including “Program Additional Key.”
- Check that you have the correct key and insert it into the ignition.
- When you press “Continue,” your new key will be programmed.
Conclusion
Although Ford’s PATS system cannot be bypassed without the ignition key, there are a couple of workarounds if you have the appropriate RFID chip and how to bypass ford pats system without key. The PATS system will always register the correct code and allow you to start the vehicle if you remove the chip from the key and glue it to the ignition lock.
You now understand how to bypass the Ford PATS system without a key in a few simple steps. The PATS is an excellent anti-theft measure that is beneficial to many car owners.
We hope this guide has helped you understand everything there is to know about the PATS system, how it works, and how to disable and reset it. Please leave a comment below if you have any questions about the PATS.